http://satellite-board.de

Hallo,
ich habe heute versucht, eine neue Firmware auf meinen Easy CI zu laden, aber ich bekomme den Receiver nicht dazu, in den Download-Modus zu gehen (obwohl ich beim Start "D" drücke).
Was könnte ich falsch gemacht haben?
Vielen Dank,

Peller

Folgendes gibt Hyperterminal aus:
_______________________________________________
serial Display
2MB Hardware .. idx= 1
=====================================================
ZapTV boot ver 3.10 Sep 24 2001 at 16:35:25
CPU: TMX320AV7111, Flash 2MB
running at 0x2c100000 .. 0x2c1effff
galaxis zapping team
=====================================================
...........
Jump only first(0) Ver 10 check 803b addr 2c100000 !
serial Display
2MB Hardware .. idx= 1
=====================================================
ZapTV boot ver 3.10 Sep 24 2001 at 16:35:25
CPU: TMX320AV7111, Flash 2MB
running at 0x2c100000 .. 0x2c1effff
galaxis zapping team
================================================
...........
Jump only first(0) Ver 10 check 803b addr 2c100000 !
** SendI2cMsg err! at 70 cnt=1 ***
=====================================================
EASY project Sep 16 2002 at 10:32:31
Manufactur : galaxis, CPU: TMX320AV7111
=====================================================
** SendI2cMsg err! at 86 cnt=2 ***
** SendI2cMsg err! at 38 cnt=3 ***
** SendI2cMsg err! at 18 cnt=4 ***
** SendI2cMsg err! at 90 cnt=5 ***
** SendI2cMsg err! at ca cnt=6 ***
** SendI2cMsg err! at 6e cnt=7 ***
** SendI2cMsg err! at
** SendI2cMsg err! at 6e cnt=9 ***
** SendI2cMsg err! at 6e cnt=10 ***
** SendI2cMsg err! at 6e cnt=11 ***
** SendI2cMsg err! at 6e cnt=12 ***
** SendI2cMsg err! at 6e cnt=13 ***
** SendI2cMsg err! at 6e cnt=14 ***
** SendI2cMsg err! at 6e cnt=15 ***
** SendI2cMsg err! at 6e cnt=16 ***
** SendI2cMsg err! at 6e cnt=17 ***
** SendI2cMsg err! at 6e cnt=18 ***
** SendI2cMsg err! at 6e cnt=19 ***
** SendI2cMsg err! at 6e cnt=20 ***
** SendI2cMsg err! at 6e cnt=21 ***

---- End of system check ----

------------------------------------------------------
DRAM Base: 0x2e000000 Size: 2 MB
SDRAM Base: 0xcc200000 Size: 4 MB
SVC St Base: 0x2e006544 Size: 0x80
UDF St Base: 0x2e0065c4 Size: 0x80
ABO St Base: 0x2e006644 Size: 0x80
IRQ St Base: 0x2e0066c4 Size: 0x800
Priv Base: 0x2e021468 Size: 0x80
Heap Base: 0x2e0214e8 Size: 0x1d6917
Stack Base: 0x2e1f7e00 Size: 0x8000
SDHeap Base: 0xcc200000 End: 0xcc3fffef
Flash1: 1 - ATMEL AT49BV1614 , 5 waits
EEPROM: 24C16 (2Kx8)
Display: 80C51 Display
Frontend: SAT Alps BSRU6
AudioV Mux: STV6410 2 scart
Dolby AC3: Dolby AC3 CS8405a
RF Modul: ---
Modem: ---
Common IF: CIMaX 2 Slot
Beta IF: ---
Tcontrol : off
MacroVision: ---
Upd sw ver.: not available, ASTRA 92/92
------------------------------------------------------
=== DEVICE on ====
___________________________________________

so, Fehler gefunden. Mein gender-changer hat nicht funktioniert (also mal wieder der User schuld

Schönen Gruß,

Peller